S. A. S. Nagar, Mohali, Punjab
- GST NO. : 03DJQPB9541F1Z8
Compressed Air Dryers
Leading Manufacturers, Wholesaler, Trader, Distributor of Desiccant Compressed Air Dryer, Medical Breathing Air Dryer and Refrigerated Air Dryer from Mohali.
| Business Type | Manufacturer, Supplier |
| Brand Name | FS Curtis |
| Usage | Industrial |
| Warranty | 1 Year |
| Finishing | Polished |
| Packaging Type | Carton Box |
FS CURTIS air dryer offers total drying solution for compressed air. Drying Cycle: Moist air from the compressor is sent through the coalescing filter where water and oil coalesce and get purged through the auto drain valve. The relatively clean and moist air passes through the drying tower filled with desiccantand gets completely dried up to the desired dew point. The desiccant fines, if any, are completely removed through a built in after filter.
Regeneration Cycle: During this cycle, the sudden depressurization brings out water molecules trapped in the desiccant pores to the surface of the beads. A small portion of the dry compressed air from the drying tower then passes over the desiccant through the regeneration orifice, to ensure complete regeneration of the desiccant.
| Business Type | Manufacturer, Supplier |
| Brand Name | FS Curtis |
| Material | MS |
| Warranty | 1 Year |
| Finishing | Polished |
| Packaging Type | Carton Box |
| Specialities | Fine Finish, Precisely Designed |
FS CURTIS medical dryers deliver a dewpoint of below 0 C as mandated by NFPA 99. The FS CURTIS medical dryers operate with the principle of Pressure Swing Adsorption, hence removing more moisture than refrigeration air dryers, and delivers moisture free dry air consistently irrespective of flow variation.
Based on medical application criticality, the package comes with one working and one
stand by dryer. So there is no need to stop the air dryers for maintenance. Purge saving system saves purge air upto 60% for a typical hospital load of 30% to 40%. Dewpoint and CO monitor enables to monitor dewpoint and CO levels as mandated by NFPA 99.
| Business Type | Manufacturer, Supplier |
| Material | Mild Steel |
| Warranty | 1 Year |
| Finishing | Polished |
| Display Type | Manual |
| Packaging Type | Packet |
| Brand | FS Curtis |
HEAT EXCHANGER WITH MOISTURE SEPARATOR Our Heat Exchanger comprises of Pre cooler, Evaporator and built in Stainless Steel demister moisture separator.
Cross flow type Pre cooler (air to air heat exchanger) and evaporator (air to refrigerant heat exchanger) ensure more cross sectional area for flow to make it non-clogging. Heat exchanger is designed to have better turbulence & maximized heat transfer rate.
Lesser difference in temperature between Inlet Air & Outlet Air ensures better effectiveness. Piping is completely eliminated and the air passage is non-ferrous.
The heat exchanger assembly is encapsulated by PUF Insulation (Eco friendly) to prevent the loss of cooling effect.
Non-Cyclic Refrigeration System
HOT GAS BY-PASS Value automatically maintains dew point temperature across a wide range of load and ambient conditions without the need for any adjustments. High pressure, high temperature refrigerant vapor is introduced after the expansion value to ensure temperature control.
Automatic Condensate Drain
Adjustable electronic timer controlled: Pilot operated / direct: compressed air powered Auto drain valve. Positive discharge of heavily contaminated condensate.
Ease Of Installation:
All dryers are shipped pre-piped and wired, ready to install and operate. Installation is made easy with conveniently located Air and Drain connections.
Environmental
FS CURTIS DRYERS are designed to have low energy usage, helping to conserve the Earth's Resources and minimize pollution. Refrigerants are with zero ozone depletion factor, and thereby making FS CURTIS dryers' 'OZONE FRIENDLY'.
